Leading 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.

Don't take too lightly the forklift at the office. If the procedure is bad, there will certainly be significant accidents in minutes, and there are numerous mishaps including forklifts.

Situation 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead can not be located, causing a moving mishap.
Situation 2: In order to preserve the balance of the forklift when lifting heavy goods, the employees utilized their body weight as the weight, which virtually created casualties.
Situation 3: The width of the forklift cargo exceeds the allowable size of the course and holds on the roadside shelf, which almost causes an crash.
Instance 4: Forklift is speeding up and rolls over during a turn.
Instance 5: The forklift vehicle driver did not observe the pedestrian, and the pedestrian did not observe the forklift.
Case 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not put on the safety belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not use a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift procedure should pay attention to these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn initially and after that start.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be safe prior to beginning.
3. When the forklift starts with a lots, the motorist should initially confirm that the tons is stable and trustworthy.
4. The begin has to be slow and constant.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground should be maintained 300mm-400mm, and the pole should be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When entering and leaving the task website or while driving, be careful that there will be no barriers in the sky. When the tons is taking a trip, the fork must not be increased expensive, which will impact the security of the forklift. .
3. After unloading, the fork ought to be decreased to the regular driving position before driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal ought to be released initially. High-speed sharp turns are restricted. High-speed doglegs will certainly create the vehicle to lose lateral stability and topple. .
5. When the forklift is downhill, it is purely restricted to turn off the flame and slide, and it is forbidden to brake unexpectedly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it should follow the web traffic rules in the manufacturing facility and have to maintain a particular safety and security range from the car ahead. .
7. When the forklift is running, the tons needs to remain in the most affordable placement that does not prevent the driving, and the gantry needs to be properly slanted back. The lots will not be elevated other than when piling or packing. .
8. The height of the tons should not block the chauffeur's sight. In special circumstances, when the item influences the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The secure driving rate of the forklift in the manufacturing facility area is 5 km/h, and it must drive securely at a reduced rate when going into the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for employees to depend on the fork to hold products and play a balancing role. .
12. If troubles are discovered, they will be repaired and reported in a prompt way, and they will never ever operate with illnesses or hide them.

packing and unloading.
1. When fork-loading things, the range between both forks must be adjusted as required to make the tons of the two forks well balanced and not skewed, and one side of the item must be against the shelf. .
2. It is prohibited to work with a solitary fork or utilize a fork top or draw. In special circumstances, safety and security warning signs have to be set up to advise surrounding pedestrians. .
3. In the process of loading and discharging items, the forklift needs to be braked with the brake. .
4. The rate of the vehicle need to be sluggish and constant. Beware not to roll the wheels on the dunnage, so as not to extend the rolled objects and injure people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as Electric Forklift Truck for Warehouse feasible under the load, and it ought to be kept in mind that the fork suggestion need to not touch other products or things. The tons needs to be stabilized with very little back tilt of the gantry so that the tons does not glide in reverse. The mast can be slanted onward a little when the load is reduced to permit easy positioning of the lots and extraction of the forks. .
6. It is prohibited to fork items at broadband and collide with difficult things with the fork head. .
7. When the forklift is functioning, it is forbidden for people to loaf the fork, so regarding avoid the collapse of the goods and hurt people. .
8. Overwhelming is forbidden, and it is banned to use forks to lift workers to take part in high-altitude procedures to stay clear of high-altitude falling accidents. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll things. .
10. It is not permitted to use forks to pick, turn pallet unload.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you need to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the driver does not leave the vehicle's line of sight and does not exceed 1 min).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the appearance ought to be checked, and fuel, lubricating oil and air conditioning water must be included.
2. Inspect the security performance of starting, running and stopping.
3. Examine whether the lights and horn signals are total and efficient.
4. During the operation of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the external leak must likewise be checked and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You need to inspect before leaving the car;.
2. When you encounter a person in front of you during driving, you need to send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline ought to be slow and consistent, and no turning on the incline is allowed.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the vehicle must be driven backwards when worsening;.
8. When the forklift personnel lug the goods and progress, if they run into big or hefty products and most likely to the chauffeur's view, they ought to take the turning around exercise
.
The "Eight Prohibitions" must be followed in the operation.
1. Solitary fork operation is not enabled.
2. It is not allowed to lift the goods for cross country driving.
3. It is not permitted to pick up the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not enabled to make use of inertia force to get the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following problems.
1. Contours, slim roads, railway crossings;.
2. Sections with a longitudinal slope above 5%.
3. When there is an barrier on one side of the road, the opposite side of the section with the exact same size as Stand-on Electric Pallet Stacker the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844